Iron Nest Firing Solution Guide: Plot, Calculate, Load, and Fire

Official Iron Nest screenshot showing the heavy turret firing at night

A reliable shot in IRON NEST: Heavy Turret Simulator depends on keeping three different measurements separate. Reported bearings and distances locate the target. The line from the exact Iron Nest position to that target supplies the gun’s bearing and range. The Ballistic Calculator, or the manual fallback below, converts the range and powder-charge count into elevation. Mix those jobs, and a perfectly loaded gun can still miss.

This guide covers the full Steam game, App ID 2950790, through Patch 1.0 (1558) dated August 8, 2026. That patch fixed elevation and elevation-linkage controls failing to reset after leaving a mission after firing. It did not change the firing method described here. Mission coordinates, available ammunition, and special objectives can vary, so use the current order for values and this article for the operating method.

Separate observation geometry from gun data

Open High Command and Field Intelligence before touching the map. Copy the current mission lines to the Clipboard, then remove anything left from an earlier target. For one solution you need to know which point is the Iron Nest, which points are spotters or references, where every bearing or distance begins, and whether the order requires a particular target or shell choice.

A bearing reported from Spotter 2 helps locate the target. It is not the turret bearing. Keep the origin attached to every copied measurement; a number without its origin is unsafe to use.

Official Iron Nest screenshot of the tactical map and plotting tools

The tactical map has a 20-by-10 main grid, and each main cell contains a 10-by-10 sub-grid. Place the Iron Nest, blue spotters, and green reference points at their full coordinates, including the sub-cell digits. Then reproduce the report:

  • Draw a bearing from the point named in the report and extend it far enough to meet the other construction.
  • For a reported distance, use the compass to draw that radius from its named origin.
  • Mark the intersection of the supplied lines or circles with the red target token.

The red, yellow, and white pencils measure in the same way. Their practical value is visual separation, so use different colors when several construction lines overlap. If the lines almost meet, do not average the gap. Recheck the origin token, the main-cell coordinate, the sub-cell digits, and the report attached to that origin.

The final line must begin at the Iron Nest

Once the target has a defensible sub-cell, draw a fresh line from the exact Iron Nest sub-cell to the red target token. The bearing and range from this line are the values to use at the gun. A spotter line helped locate the target, but it cannot replace this final measurement.

Reserve one pencil color for the Nest-to-target line. Before leaving the map, read its bearing and range together and make sure both are on the Clipboard. If the Nest token was placed only approximately, correct it now: a small origin error grows into a large lateral error over a long shot.

Use one calculation for the ticket and the load

Official Iron Nest screenshot of the Ballistic Calculator

Transfer the final Nest-to-target bearing and range to the Ballistic Calculator. Select the shell required by the order, or the mission-relevant shell when the choice is left to you. Choose a powder-charge count whose displayed range covers the shot, then calculate.

The result is a single firing ticket: the shell, powder charges, bearing, and elevation all belong to the same calculation. If you change the shell, range, or charge count, calculate again. Do not keep the old elevation and try to compensate elsewhere.

Manual elevation when the calculator is unavailable

If a mission leaves the calculator unavailable, two current community guides agree on the simplified in-game rule. With range in metres:

elevation = range × 0.012 ÷ powder charges

If you are reading range in kilometres, the equivalent form is:

elevation = range × 12 ÷ powder charges

For example, a range of 6.47 km with two charges gives 6.47 × 12 ÷ 2 = 38.82. With six charges, the kilometre value is simply doubled, so 6.47 km gives 12.94 degrees. Keep the unit explicit: entering 6470 as though it were kilometres creates a result one thousand times too large.

This formula replaces only the elevation calculation. You still need the correct target point, Nest-to-target bearing and range, shell, charge count, and matching load.

Load the shell before its powder charges

Official Iron Nest screenshot of powder charges on the loading tray
  1. Index the shell carousel until the projectile named by the current solution reaches the loading position.
  2. Run the shell rammer and wait until its ram has fully retracted.
  3. Dispense the exact powder-charge count used by the calculator or manual formula.
  4. Ram the powder and let the breech finish closing and locking.

Do not place powder on the tray while the projectile ram is still extended. The cannon loads at neutral elevation, and elevation control remains unavailable until loading completes. You can begin traversing toward the required bearing during the loading cycle, but do not treat that saved time as permission to set elevation early.

If the shell or charge count does not match the current solution, stop before arming. Public references do not establish one unloading method for every situation, so this guide does not invent one. Restore a consistent calculation and load using the controls and instructions available in the current mission.

Bearing moves the turret; elevation moves the selected gun

Lay the weapon on two separate axes:

  • Turret bearing: use the traversal lever for the large rotation, ease it back toward centre before the target angle, and finish with the traversal handwheel.
  • Gun elevation: after the breech locks, use the selected gun’s elevation lever for the coarse move. Wait until powered movement stops, then use its handwheel for the final setting.

Do not turn the fine elevation wheel while the powered elevation mechanism is still moving; the control can jam. Bring the heavy traversal lever back smoothly as well. The rotation counter must equal the final Nest-to-target bearing, while the selected gun’s elevation counter must equal the calculated elevation. The same number placed on the wrong control is still wrong.

Fire only when all four ticket values still agree

At the firing station, compare the current solution with the physical gun. Confirm the shell, powder-charge count, turret bearing, selected gun, and that gun’s elevation. Select and arm the intended gun, complete the firing-console switches, and use the central firing control only after every value agrees.

After impact, return to the tactical map and read the result together with any new High Command or Field Intelligence message. A corrected target point or changed range requires another plot and another calculation. Reusing an old ticket after the target data changes is not a correction.

Read the direction of a miss before changing anything

A left-or-right error points first to the horizontal data: the exact Nest position, the final Nest-to-target line, or the turret bearing. A short-or-long error points first to the range, powder charges, or elevation. This distinction prevents you from “fixing” a lateral plotting mistake with extra powder or hiding a range mistake by changing the bearing.

If the map constructions do not intersect, the error is earlier than the gun; return to the named origins and full coordinates. If elevation is still locked, finish the projectile, powder, and breech sequence. If a control state remains wrong after leaving a mission, confirm that the game is updated beyond the pre-1558 build before treating it as a new mechanical fault. If coarse and fine controls were moved together and the mechanism stopped responding, repair it and verify the setting again rather than accepting a near value.

The task is closed when one current target produces one consistent set of four values, the physical load and both axes match that set, and the post-shot map confirms the result. When any of those checks fails, change only the stage indicated by the evidence and rebuild every dependent value after it.

The verified PC release is available on Steam.